SBA CCNA1 FULL Version 2013

loading...

iklan tautan

SBA CCNA1 FULL Version :

=========================VERSI 1========================

1- ENetwork Basic Configuration PT Practice SBA 2013 (Versi 1)

A few things to keep in mind while completing this activity:

1. Do not use the browser Back button or close or reload any exam windows during the exam.
2. Do not close Packet Tracer when you are done. It will close automatically.
3. Click the Submit Assessment button to submit your work.

Introduction

In this practice Packet Tracer Skills Exam, you will:

• design and implement an addressing scheme to meet stated requirements
• configure, verify, and troubleshoot connectivity between all devices in the network

Addressing Table

Device	Interface	Address	Subnet Mask	Default Gateway
Router1	Fa0/0	172.16.1.1	255.255.255.224	n/a
	Fa0/1	172.16.1.33	255.255.255.240	n/a
Switch1	VLAN1	172.16.1.2	255.255.255.224	172.16.1.1
PC1	NIC	172.16.1.30	255.255.255.224	172.16.1.1
PC2	NIC	Preconfigured (172.16.1.35)	Preconfigured (255.255.255.240)	Preconfigured (172.16.1.33)

NOTE: The initial network has some errors. To aid in configuring and verifying the devices, as well as in troubleshooting the existing errors, use a printed version of these instructions to fill in the missing address information in the table during Step 1.

Step 1: Determine the IP Addressing Scheme.

Design an addressing scheme and fill in the Addressing Table based on the following requirements:

a.     Subnet the address space 172.16.1.0/24 to provide 30 host addresses for LAN 1 while wasting the least amount of address space.

b.    Assign the first available subnet to LAN 1.

c.     Assign the lowest (first) host address in this subnet to the Fa0/0 interface on Router1.

d.    Assign the second address in this subnet to the VLAN 1 interface on Switch1.

e.     Assign the highest (last) host IP address in this subnet to PC1.

Step 2: Configure Router1.

a.     Configure Router1 with these basic parameters:

·         Use Router1 as the router name.

·         Use class as the encrypted password for privileged EXEC mode.

·         Require password-protected logins for the console line.  Use cisco as the password.

·         Require password-protected logins for the vty lines.  Use cisco as the password.

·         Configure the banner message-of-the-day as Authorized access only!

b.    Configure the two Fast Ethernet interfaces.

·         Configure the router interfaces according to your completed addressing table.

·         Configure each interface with a description.

c.     Close the terminal window after completing the router configuration.

Step 3: Configure Switch1 and Verify Connectivity.

a.     Remove the console connection between PC1 and Router1.

b.    Connect PC1 to the Switch1 console port.

c.     Configure Switch1 with these basic parameters:

·         Use Switch1 for the switch name.

·         Use class as the encrypted password for privileged EXEC mode.

·         Require password-protected logins for the console line.  Use cisco as the password.

·         Require password-protected logins for the vty lines.  Use cisco as the password.

·         Configure the banner message-of-the-day asAuthorized access only!

d.    Configure interface VLAN 1.

e.     Configure the default gateway.

f.     Test that Switch1 is able to ping the default gateway.

Step 4: Configure and Verify PC1 Addressing.

a.     Use the IP addressing you determined in Step 1 and configure PC1 with the correct addressing.

b.    Test that PC1 is able to ping the default gateway.

Step 5: Verify and Troubleshoot End-to-End Connectivity.

Verify that PC1 is able to ping PC2. If the ping fails, locate and correct any errors. For example, make sure PC2 is configured correctly with appropriate addressing for the subnet it belongs to.

Packet Tracer Image:

Step 2: Configure Router1.

Router>enable

Router#configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#hostname Router1

Router1(config)#enable secret class

               

Router1(config)#line console 0

Router1(config-line)#password cisco

Router1(config-line)#login

Router1(config-line)#exit

Router1(config)#line vty 0 4

Router1(config-line)#password cisco

Router1(config-line)#login

Router1(config-line)#exit

Router1(config)#banner motd #Authorized access only!#

Router1(config)#interface fastEthernet 0/0

Router1(config-if)#ip address 172.16.1.1 255.255.255.224

Router1(config-if)#description LAN1

Router1(config-if)#no shutdown

Router1(config-if)#

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router1(config-if)#exit

Router1(config)#interface fastEthernet 0/1

Router1(config-if)#ip address 172.16.1.33 255.255.255.240

Router1(config-if)#description LAN2

Router1(config-if)#no shutdown

Router1(config-if)#

%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

Router1(config-if)#do show ip interface brief

Interface              IP-Address      OK? Method Status                Protocol

FastEthernet0/0        172.16.1.1      YES manual up                    up

FastEthernet0/1        172.16.1.33     YES manual up                    up

Vlan1                  unassigned      YES unset  administratively down down

Router1(config-if)#do write

Building configuration...

[OK]

Router1(config-if)#

Step 3: Configure Switch1 and Verify Connectivity.

Switch>enable

Switch#configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Switch(config)#hostname Switch1

Switch1(config)#enable secret class

Switch1(config)#line console 0

Switch1(config-line)#password cisco

Switch1(config-line)#login

Switch1(config-line)#exit

Switch1(config)#line vty 0 4

Switch1(config-line)#password cisco

Switch1(config-line)#login

Switch1(config-line)#exit

Switch1(config)#banner motd #Authorized acccess only!#

Switch1(config)#interface vlan 1

Switch1(config-if)#ip address 172.16.1.2 255.255.255.224

Switch1(config-if)#no shutdown

Switch1(config-if)#

%LINK-5-CHANGED: Interface Vlan1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up

Switch1(config-if)#exit

Switch1(config)#ip default-gateway 172.16.1.1

Switch1(config)#^Z

Switch1#

%SYS-5-CONFIG_I: Configured from console by console

Switch1#show ip interface brief

Interface              IP-Address      OK? Method Status                Protocol

FastEthernet0/1        unassigned      YES manual up                    up

............

...........

Vlan1                  172.16.1.2      YES manual up                    up

Switch1#write

Building configuration...

[OK]

Switch1#ping 172.16.1.1

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 172.16.1.1, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 2/17/38 ms

Switch1#

Step 4: Configure and Verify PC1 Addressing.

=========================VERSI 2========================

2- ENetwork Basic Configuration PT Practice SBA 2012

A few things to keep in mind while completing this activity:

1- Do not use the browser Back button or close or reload any Exam windows during the exam.

2- Do not close Packet Tracer when you are done. It will close automatically.

3- Click the Submit Assessment button to submit your work.

Introduction

In this practice Packet Tracer Skills Exam, you will:

• design and implement an addressing scheme to meet stated requirements
• configure, verify, and troubleshoot connectivity between all devices in the network

Addressing Table

Device	Interface	Address	Subnet Mask	Default Gateway
HQ	Fa0/0	10.10.10.1	255.255.255.192	n/a
	Fa0/1	10.10.10.65	255.255.255.248	n/a
S2	VLAN1	10.10.10.2	255.255.255.192	10.10.10.1
NetAdmin	NIC	10.10.10.62	255.255.255.192	10.10.10.1
H1	NIC	Preconfigured (10.10.10.67)	Preconfigured (255.255.255.248)	Preconfigured (10.10.10.65)

NOTE: The initial network has some errors. To aid in configuring and verifying the devices as well as troubleshooting the existing errors, use a printed version of these instructions to fill in the missing address information in the table during Step 1.

Step 1: Determine the IP Addressing Scheme.

Design an addressing scheme and fill in the Addressing Table based on the following requirements:

a.     Subnet the address space 10.10.10.0/24 to provide 40 host addresses for LAN 1 while wasting the least amount of address space.

b.    Assign the first available subnet to LAN 1.

c.     Assign the lowest (first) host address in this subnet to the Fa0/0 interface on HQ.

d.    Assign the second address in this subnet to the VLAN 1 interface on S2.

e.     Assign the highest (last) host IP address in this subnet to NetAdmin.

Step 2: Configure HQ.

a.      Configure HQ with these basic parameters:

·         Use HQ as the router name.

·         Use class as the encrypted password for privileged EXEC mode.

·         Require password-protected logins for the console line.  Use cisco as the password.

·         Require password-protected logins for the vty lines.  Use cisco as the password.

·         Configure the banner message-of-the-day as Unauthorized access is prohibited.

b.    Configure the two Fast Ethernet interfaces:

·         Configure the router interfaces according to your completed Addressing Table.

·         Configure each interface with a description.

c.     Close the terminal window after completing the router configuration.

Step 3: Configure S2 and Verify Connectivity.

a.     Remove the console connection between NetAdmin and HQ.

b.    Connect NetAdmin to the S2 console port.

c.     Configure S2 with these basic parameters:

·         Use S2 for the switch name.

·         Use class as the encrypted password for privileged EXEC mode.

·         Require password-protected logins for the console line.  Use cisco as the password.

·         Require password-protected logins for the vty lines.  Use cisco as the password.

·         Configure the banner message-of-the-day as Unauthorized access is prohibited.

d.    Configure interface VLAN 1.

e.     Configure the default gateway.

f.     Test that S2 is able to ping the default gateway.

Step 4: Configure and Verify NetAdmin Addressing.

a.     Use the IP addressing you determined in Step 1 and configure NetAdmin with the correct addressing.

b.    Test that NetAdmin is able to ping the default gateway.

Step 5: Verify and Troubleshoot End-to-End Connectivity.

Verify that NetAdmin is able to ping H1. If the ping fails, locate and correct any errors. For example, make sure H1 is configured correctly with appropriate addressing for the subnet it belongs to.

Packet Tracer image:

Step 2: Configure HQ.

Press RETURN to get started!

Router>enable

Router#configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#hostname HQ

HQ(config)#enable secret class

HQ(config)#line console 0

HQ(config-line)#password cisco

HQ(config-line)#login

HQ(config-line)#exit

HQ(config)#line vty 0 4

HQ(config-line)#password cisco

HQ(config-line)#login

HQ(config-line)#exit

HQ(config)#banner motd #Unauthorized access is prohibited.#

HQ(config)#interface fastEthernet 0/0

HQ(config-if)#ip address 10.10.10.1 255.255.255.192

HQ(config-if)#description LAN1

HQ(config-if)#no shutdown

HQ(config-if)#

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

HQ(config-if)#exit

HQ(config)#interface fastEthernet 0/1

HQ(config-if)#ip address 10.10.10.65 255.255.255.248

HQ(config-if)#description LAN2

HQ(config-if)#no shutdown

HQ(config-if)#

%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

HQ(config)#

Step 3: Configure S2 and Verify Connectivity.

Switch>enable

Switch#configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Switch(config)#hostname S2

S2(config)#enable secret class

S2(config)#line console 0

S2(config-line)#password cisco

S2(config-line)#login

S2(config-line)#exit

S2(config)#line vty 0 4

S2(config-line)#password cisco

S2(config-line)#login

S2(config-line)#exit

S2(config)#banner motd #Unauthorized access is prohibited.#

S2(config)#interface vlan 1

S2(config-if)#ip address 10.10.10.2 255.255.255.192

S2(config-if)#no shutdown

S2(config-if)#

%LINK-5-CHANGED: Interface Vlan1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up

S2(config-if)#exit

S2(config)#ip default-gateway 10.10.10.1

S2(config)#exit

S2#

%SYS-5-CONFIG_I: Configured from console by console

S2#ping 10.10.10.1

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.10.10.1, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 31/34/47 ms

S2#write

Building configuration...

[OK]

S2#

loading...